Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Before
After
Before
After
Before
AfterPGT Roofing: The Rancho Cucamonga Owner’s Guide
PGT roofing components in Rancho Cucamonga typically run $400-$1,800 to repair and $8,000-$20,000 for full replacement, with most common part failures addressed same-day when we stock the piece. We carry PGT-compatible membrane sections, flashing kits, and ridge vent assemblies on our Rancho Cucamonga trucks, and we install them under the 365-Day Done Right Promise. Most owners discover a PGT roofing failure after a Santa Ana wind event or the first hard rain of October, when a section of membrane lifts or a vent seal that held through summer finally lets go.
Which PGT Models This Applies To
PGT Industries produces several roofing-adjacent systems, but the parts we handle most often in Rancho Cucamonga are the PGT Targa and PGT WinGuard roof-access skylight assemblies, plus the PGT low-profile ridge vent systems specified for tile and shingle roofs in the Inland Empire climate zone. The critical identifier is the stamped aluminum label on the vent frame or skylight curb, which lists a six-digit PGT part number starting with 28- or 31-. If that label is sun-faded, measure the curb width: Targa series runs 22 inches, WinGuard roof units run 24.5 inches, and mixing the flashing kit between the two guarantees a leak.
We source OEM PGT parts through the manufacturer’s Florida distribution, though for certain ridge vent components we use a quality aftermarket equivalent from Lomanco that matches the CFM rating and nail pattern. The aftermarket saves roughly 15% on parts cost and carries the same 20-year material warranty; we note the origin on your written quote so you know what you’re getting. One compatibility gotcha: PGT’s 2018-2021 ridge vent runs a 4.5-inch flange, while 2022+ switched to 5-inch. We check this on every Rancho Cucamonga job because the wrong flange leaves a 0.5-inch exposure that the 110-degree summer sun will find in two seasons.
Signs Your PGT Roofing Is Failing
- Water stains on the ceiling below a skylight or vent. The butyl tape seal between the PGT curb and the roof deck has thermocycled past its service life. In Rancho Cucamonga’s 40-degree morning to 95-degree afternoon swings, that tape typically hardens in 8-12 years, not the 20-year roof life.
- Whistling or draft near the ridge line. The PGT vent baffle has detached from the nailer strip, usually from wind uplift. Santa Ana gusts at 60-plus mph will pop the baffle before they damage the shingles around it.
- Granule buildup in the gutter below a vent section. The vent is creating negative pressure that pulls shingle granules into the channel, which means the vent opening is misaligned or the internal damper is stuck open.
- Daylight visible through the vent from the attic. The PGT mesh screen has torn or the end cap has walked out of position. This is the failure point for rodent entry in Rancho Cucamonga’s foothill neighborhoods.
- Skylight glass fogs between panes. The PGT insulated glass unit has lost its argon fill. This is cosmetic until the seal fails completely, but in our experience the glass will crack within 18 months once fogging starts.
Before
AfterReplacement Cost & What’s Included
| Service | Price Range in Rancho Cucamonga | What’s Included |
|---|---|---|
| PGT ridge vent section repair | $400-$900 | Remove damaged section, install OEM or Lomanco equivalent, re-nail per PGT pattern, replace surrounding shingles as needed |
| PGT skylight curb reflash | $600-$1,400 | Remove skylight, replace butyl tape and ice-and-water shield, reset unit, test for drainage |
| PGT skylight glass replacement | $800-$1,800 | Order IGU from PGT, remove sash, install new glass, reseal curb |
| Full roof replacement with PGT vents | $8,000-$20,000 | Tear-off, deck inspection, new underlayment, shingles or tile, all PGT vents replaced or reinstalled with new flashing |
The range depends on roof pitch, access, and how many PGT components need attention. Under Clause 1 of the Haven Standard, your written quote itemizes every part and labor hour before we start. No change proceeds without a signed change order. The 365-Day Done Right Promise covers our workmanship; OEM parts carry the manufacturer’s material warranty, which we register for you.
DIY or Call Us?
There’s a safe middle ground here. A homeowner can check the PGT label, measure the curb, and photograph the failure from the attic or ground with a zoom lens. What we don’t recommend: climbing a tile roof in Rancho Cucamonga’s October wind season, or attempting to reseal a PGT skylight curb from above without proper fall protection. The curb sits on a raised frame that requires removing the unit entirely to do the job right; partial resealing traps water and rots the deck.
We also don’t suggest ordering PGT parts by part number alone. The 4.5-inch versus 5-inch flange issue, the Targa versus WinGuard curb dimension, and the nail pattern for your roof sheathing thickness all affect what ships. We stock the common configurations on our Rancho Cucamonga trucks because we’ve measured them on site before. Call (909) 373-9612 and we’ll confirm what you need before anyone picks up a tool. Measure twice, document once, no surprises at closeout.
FAQs
PGT ridge vents and skylight curbs typically last 12-15 years in the Inland Empire before the sealant or baffle needs attention, though the roof itself may have 20-plus years of life remaining. The thermal cycling here is harder on flexible components than on the rigid roofing materials around them. Call (909) 373-9612 for an exact quote on replacement - estimates are free.
The glass unit and the curb flashing can be repaired independently; the aluminum frame itself rarely fails unless physically damaged. If the frame is sound, we replace the failed component and preserve the rest. Call (909) 373-9612 for an exact quote - estimates are free.
A single ridge vent section or skylight reflash takes 3-5 hours on site, assuming standard pitch and clear attic access. Ordering the correct PGT part adds 3-5 business days if we don’t stock it; we carry the common Rancho Cucamonga configurations and can often do same-day work. Call (909) 373-9612 to check current truck stock.
We stock PGT-compatible ridge vent assemblies, standard curb dimensions, and Lomanco aftermarket equivalents on our Rancho Cucamonga trucks. Specialty sizes and custom IGUs ship from PGT’s Florida facility with a 5-7 day lead time. Call (909) 373-9612 with your part number and we’ll tell you what’s available today.
Rowan Construction Group Rancho Cucamonga is an independent service provider and is not affiliated with PGT Industries. We also stock parts for KraftMaid, Cambria, and Silestone products across our seven trades.
Ready to get the exact number in writing? Call (909) 373-9612 to schedule your free estimate. We’ll inspect the PGT component, confirm the part match, and deliver a flat written price with itemized scope before any work starts - that’s Clause 1 of the Haven Standard, and it’s been our practice since 2007.
Written by Grant Rowan, Owner, Rowan Construction Group - Rancho Cucamonga, CA at Rowan Construction Group Rancho Cucamonga, serving Rancho Cucamonga and nearby areas.